We all like to use something unique, something stylish with your style. Accessories give us a personal feel, with items such as earrings and pendants being preferred by many. These items are now increasingly made of acrylic materials, rather than traditional wood, steel, and plastic. That's why Internet users have recently been Googling how to make acrylic earrings.
Why are laser engraving machines better for acrylic earrings?
So, why acrylic, right? Well, go to any platform for buying DIY and art (like Etsy). There, you'll find acrylic earrings, which have reached their peak in fashion accessories due to their ability to offer different colors and lightweight, and flexible designs. As you may know, laser engraving/cutting technology has improved significantly over the years and is now also being used to develop unique acrylic earrings.
Using a laser beam, the corners of the earrings are clean and smooth. The overall design is also very detailed, the engraving pattern is smooth, and it is difficult to complete with traditional technology, so most of them do not need secondary operations. Not to mention, laser beams are very efficient and can be used to make earrings; It takes a few seconds to buy a nice pair of earrings.
Such results can only be achieved using reliable laser engraving machines and engraving machines such as the Ortur LM3 laser cutting machine. The legendary hardware is powered by its software "Inspiraesth" and features four laser beams of 5 watts (for a total of 20 watts) sent out via ultra-precise focusing rods. In addition, you can use dual fans at 10,000 RPM and guide shutters for full ventilation, so that your ears can stay cool while sculpting.
To use the Limited edition Ortur Laser Master 3 or any other laser engraver in your garage, here's the right way to make acrylic earrings:
Create a design file.
The best way to do this is to draw your idea of an earring on a piece of paper. The shape, pattern, and size of the earrings should be carefully considered to prove the uniqueness of the earrings.
When this is done, the graphics are converted to vector format in the computer (for example, to vector, SVG, DXF, AI). In these vector files, the "graph path" is useful in the guidance of the laser engraving machines to improve accuracy. Instead of using the same color to show cut and sculpted lines in the design file, try using a new color or layer.
Understand acrylic types
When you delve into the acrylic world, you'll find two materials used to make acrylic earrings: Cast acrylic, which is preferred for laser cutting due to its smooth, clean edges and superior sculpting quality. The second is extruded acrylic, which is usually cheaper but may not produce as clean a cut as pouring acrylic.
Extrusion is easier to melt and less suitable for complex designs. The speed, power, and number of passes required to cut acrylic sheets depend on the sheet width you are using. We recommend choosing a cast acrylic sheet between 1.5mm and 3mm for earrings.
Test and execution
It's best to make it out of cardboard or waste acrylic before you move on to cutting the last piece. This helps to influence changes to any design defects that would otherwise be unwise to change due to the use of quality acrylic panels.
After the test, the acrylic sheet is placed on the cutting table of the laser engraving machines. If the bracket is small enough with enough room to move, you can also use masking tape to secure it. Start the laser cutting process from the software of the laser device and observe the entire process. Make sure all cuts are smooth and all carvings are correct. In the case of the Ortur LM3, there is a good chance that this process will go smoothly.
Smooth out
Once finished, there may be some residue or burn marks on the acrylic resin after cutting. Wash your splinters with mild soap and water, or just use a cleaner specific to acrylic splinters. Although the LM3's ventilation system will remove any buildup just in case, check for residue.
finishing
We assume your design will also include earring hooks or other finds, which means you'll need to drill small holes (some designs have laser-cut holes). To make such holes, it is recommended to always work at a low speed, as high speeds can crack the acrylic surface.